我有这个拓扑
我正在研究路由图和 pbr 和分发列表，我从 R4 和 R5 和 R7 发布一堆网络地址，我设法利用路由映射和分发列表通过在 eigrp 中应用分发列表入站从 R6 路由表中删除某些条目，据我了解，这只会影响传入路由，因此 R7 应该只获得 R6 RIB 的过滤版本，但这是在 R6 上应用分发列表时奇怪的事情，R7 地址不会被通告给 R6，当然也不会通告给其他路由器，所以我的问题是我应该如何保持分发列表的相同行为并同时宣传 R7 地址？我应该改变什么？谢谢
R6#sh ip int brie | ex unassigned
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 172.16.56.6 YES NVRAM up up
GigabitEthernet1/0 172.16.46.6 YES NVRAM up up
Ethernet2/0 172.16.36.6 YES NVRAM up up
Ethernet2/1 172.16.26.6 YES NVRAM up up
Ethernet2/2 10.10.10.6 YES NVRAM up up
Loopback0 6.6.6.6 YES NVRAM up up
R6#sh run
interface Ethernet2/2
ip address 10.10.10.6 255.255.255.0
ip policy route-map RM1
router eigrp 123
distribute-list route-map RM2 in
network 6.6.6.0 0.0.0.255
network 10.0.0.0
network 172.16.26.0 0.0.0.255
network 172.16.36.0 0.0.0.255
network 172.16.46.0 0.0.0.255
network 172.16.56.0 0.0.0.255
ip prefix-list PL1 seq 10 permit 55.55.0.0/16 ge 27 le 29
ip prefix-list PL2 seq 5 permit 44.44.0.0/16 ge 24 le 26
ip prefix-list PL2 seq 10 permit 44.44.0.0/16 ge 30 le 30
ip prefix-list PL3 seq 10 permit 10.7.0.0/16 ge 24
ip prefix-list PL3 seq 20 permit 10.2.0.0/16 ge 24
access-list 101 permit icmp host 10.10.10.7 any
access-list 102 permit ip any any
route-map RM2 permit 10
match ip address prefix-list PL1
route-map RM2 permit 20
match ip address prefix-list PL2
route-map RM1 permit 10
match ip address 101
set ip next-hop 172.16.56.5
route-map RM1 permit 20
match ip address 102
set ip next-hop 172.16.36.3
R6#sh ip route | ex L
6.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.10.10.0/24 is directly connected, Ethernet2/2
44.0.0.0/8 is variably subnetted, 4 subnets, 3 masks
D 44.44.2.0/24
[90/130816] via 172.16.46.4, 00:38:53, GigabitEthernet1/0
D 44.44.3.0/26
[90/130816] via 172.16.46.4, 00:38:53, GigabitEthernet1/0
D 44.44.3.80/30
[90/130816] via 172.16.46.4, 00:38:53, GigabitEthernet1/0
D 44.44.4.0/26
[90/130816] via 172.16.46.4, 00:38:53, GigabitEthernet1/0
55.0.0.0/8 is variably subnetted, 5 subnets, 3 masks
D 55.55.1.0/28
[90/130816] via 172.16.56.5, 00:38:53, GigabitEthernet0/0
D 55.55.3.0/29
[90/130816] via 172.16.56.5, 00:38:53, GigabitEthernet0/0
D 55.55.3.32/27
[90/130816] via 172.16.56.5, 00:38:53, GigabitEthernet0/0
D 55.55.4.0/29
[90/130816] via 172.16.56.5, 00:38:53, GigabitEthernet0/0
D 55.55.4.32/27
[90/130816] via 172.16.56.5, 00:38:53, GigabitEthernet0/0
172.16.0.0/16 is variably subnetted, 8 subnets, 2 masks
C 172.16.26.0/24 is directly connected, Ethernet2/1
C 172.16.36.0/24 is directly connected, Ethernet2/0
C 172.16.46.0/24 is directly connected, GigabitEthernet1/0
C 172.16.56.0/24 is directly connected, GigabitEthernet0/0
R1#sh ip route
--output ommited--
10.0.0.0/24 is subnetted, 1 subnets
D 10.10.10.0 [90/282112] via 192.168.15.5, 06:40:35, GigabitEthernet0/0
[90/282112] via 192.168.14.4, 06:40:35, GigabitEthernet1/0
R1#sh ip route
10.0.0.0/24 is subnetted, 1 subnets
D 10.10.10.0 [90/282112] via 192.168.15.5, 00:07:09, GigabitEthernet0/0
[90/282112] via 192.168.14.4, 00:07:09, GigabitEthernet1/0
[90/307456] via 192.168.13.3, 00:07:09, Ethernet2/1
[90/307456] via 192.168.12.2, 00:07:09, Ethernet2/0
R1#trac 10.10.10.7
Type escape sequence to abort.
Tracing the route to 10.10.10.7
VRF info: (vrf in name/id, vrf out name/id)
1 192.168.12.2 8 msec 20 msec 4 msec
2 * * *
3 * * *
4 * *
R2(config-if)#do trac 10.10.10.7
Type escape sequence to abort.
Tracing the route to 10.10.10.7
1 172.16.26.6 24 msec 16 msec 8 msec
2 10.10.10.7 12 msec 24 msec 28 msec
R2(config-if)#do sh run
interface Loopback11
ip address 2.2.2.222 255.255.255.255
interface GigabitEthernet0/0
ip address 192.168.12.2 255.255.255.0
interface GigabitEthernet1/0
ip address 172.16.26.2 255.255.255.0
router eigrp 123
network 2.2.2.222 0.0.0.0
network 172.16.26.0 0.0.0.255
network 192.168.12.0
我把无能的信息，如果你需要更多我会编辑帖子